説明
695 Nm @ 540 rpm
最大トルク1,200Nm
50～75馬力
Lemon Tube Profile
CE認証取得済み
ISO 9001 / TS16949
最小注文数量1個 — LGPD対応
L32 PTO Drive Shaft — Operating Torque Parameters
Source: Ever-Power Drive Line L Series Catalog — current series highlighted in orange
| シリーズ | クロスmm | kW @540 | Pk @540 | Nm @540 | 1000kW | PK @1000 | Nm @1000 | MP Nm |
|---|---|---|---|---|---|---|---|---|
| L1 | 22×54 | 12 | 16 | 210 | 18 | 25 | 172 | 320 |
| L2 | 23.8×61.3 | 15 | 21 | 270 | 23 | 31 | 220 | 450 |
| L3 | 27×70 | 22 | 30 | 390 | 35 | 47 | 330 | 640 |
| L4 | 27×74.6 | 26 | 35 | 460 | 40 | 55 | 380 | 780 |
| L5 | 30.2×80 | 35 | 47 | 970 | 54 | 74 | 520 | 1,050 |
| L6 | 30.2×92 | 47 | 64 | 830 | 74 | 100 | 710 | 1,450 |
| L32 | 32×76 | 39 | 53 | 695 | 61 | 83 | 580 | 1,200 |
概要
製品説明
L32 steps to the 35 mm cross-kit pin diameter — a significant increase from the 30.2 mm of L6. The 35×94 mm cross kit (code 7.01) delivers 1,050 Nm at 540 rpm and 1,900 Nm peak, placing L32 in the same torque class as T7N. Like T7N, L32 uses a different tube outer diameter from the lower L Series models to fit specific high-torque implement input housings that require a lemon profile but cannot accommodate the L6 tube at this power level.
The L32 designation reflects the 32-series cross-kit heritage used in European agricultural shaft standards (Bondioli & Pavesi B07 equivalent cross dimensions). For B2B buyers sourcing replacement shafts for European-specified implements, L32 is the correct technical designation — it maps directly to the B07/series 7 classification used in European OEM parts documentation, making cross-reference straightforward for European equipment service workshops operating in South America.
L32 is the top of the standard L Series range from Ever-Power Drive Line. For applications exceeding 1,050 Nm at 540 rpm on lemon tube specification, contact the Ever-Power Drive Line engineering team to discuss L Series heavy-duty or T Series T8/T9 alternatives. For standard L32 orders, お問い合わせ with your hitch dimensions and spline specification.
組立図 - 部品参照
部品の参照番号は、以下の表の部品コードに対応しています。
Component Part Numbers — L32
Source: Ever-Power Drive Line L Series Catalog
| 成分 | 外側／船外機 | 内側／インボード |
|---|---|---|
| クロスキット | 32.01 (Ø32×76) | |
| ジョイント シンプル | l32.02B+l32.01+l32.06 | l32.02B+l32.01+l32.07 |
| スプライン付きヨーク | l32.02B | |
| チューブヨーク | l32.06 | l32.07 |
| Lemon Tube | l32.03 | l32.04 |
スプラインプロファイル参照
Left: 1-3/8 inch 6-spline (Z6) for 540 rpm — Right: 1-3/4 inch 20-spline (Z20) for 1,000 rpm
主な機能
Lemon Tube Profile — Compact OD
The lemon (elliptical) tube profile reduces the outer diameter of the telescoping assembly relative to triangular-tube T Series at the same torque class. Fits European OEM implement input housings that exclude triangular tube geometry.
Sealed Cross-Kit Bearings — IP67
Double-lip sealed needle-roller bearing cups, factory-filled with EP2 lithium complex grease. Grease nipple accessible with shield fitted. Designed for 350+ hours between maintenance interventions in normal field conditions.
CE Safety Shield — Standard
CE-marked UV-stabilised HDPE bellows guard. Yellow for field visibility. Spring-clip anchors and chain points at both ends. OECD Code 4 compliant. Supplied as standard on every L Series unit.
鍛造20CrMnTi鋼製ヨーク
Drop-forged chromium-manganese-titanium alloy steel, normalised and induction-hardened at bearing seat journals. Designed for high peak-load applications without premature bearing seat wear.
全てのスプライン規格に対応
1-3/8 inch 6-spline (ISO 500 Z6), 1-3/4 inch 20-spline (Z20), and 1-3/8 inch 21-spline (Z21). Clamp yoke and push-pin locking both available. Both ends specified independently at order.
CE + ISO認証パッケージ
CE Declaration of Conformity, ISO 9001:2015, TS/16949 process certificate, and LGPD compliance documentation standard with every shipment. SGS third-party inspection available on contract orders.
代表的な用途
Typical L32 application in 50–75 hp tractor class
Large Square Baler Feeders
Feeder rotor and knotter drive on compact square balers in the 60–90 hp class. L32 handles the 1,900 Nm peak eject load with the lemon tube profile specified by several European square baler OEM lines.
Heavy-Duty Forage Harvesters
Flywheel and feed roller drive on pull-type forage harvesters. Continuous 1,050 Nm operation with high inertia peaks. Sealed L32 cross kits outperform open-bearing equivalents in sustained harvest duty.
Large Mower-Conditioners — 60–90 hp
Disc mower-conditioner main drive where the implement housing excludes the T7 triangular tube. L32 delivers the same torque class as T7N in the lemon tube profile required by this implement category.
設置およびメンテナンス
安全チェーンをトラクターと作業機の両方の固定された非回転点に取り付ける。
トルククラスを確認してください
Match implement demand (Nm) against the table above. Add 20% margin. Select the lowest L Series that meets the adjusted figure.
作業長さを調整する
治具を取り付けた状態で、連結部の中心間距離を測定します。チューブが完全に伸びた状態で50mm以上、完全に縮んだ状態で80mm以上重なっていることを確認します。
ヨーク接続を有効にする
Push-pin yoke: engage at tractor PTO stub and confirm audible click and positive retention. Clamp yoke: torque to manufacturer specification.
アンカー安全チェーン
Connect tractor-side chain to guard or tractor frame; implement-side chain to implement body. Verify taut with implement at working level.
初回使用前にグリースを塗布してください
Apply EP2 lithium complex NLGI 2 grease (2–3 pumps) to both cross-kit nipples. Service every 8 hours. Reduce to 4 hours in wet or abrasive conditions.
よくある質問
- —L32 and T7N share the same torque class (1,050 Nm at 540 rpm, 1,900 Nm peak)
- —Tube profiles differ: L32 uses lemon, T7N uses triangular — they are not interchangeable at the implement housing
- —Cross-kit pin diameter: L32 uses 35 mm (35×94 mm); T7N uses 35 mm (35×94 mm) — identical cross kits
- —Select L32 for implements specifying lemon tube; select T7N for implements specifying triangular tube
- —Yes — the L32 35×94 mm cross kit is dimensionally equivalent to the B07 series in European catalog standards
- —For cross-reference ordering, specify 35×94 mm with double-lip sealed cups
- —Ever-Power Drive Line supplies these under code 7.01 — specify when ordering
- —Wide-angle CV joints for L32 lemon tube are available as OEM order option
- —Standard cardan joint max angle: 25 degrees continuous; CV joint: up to 50 degrees
- —MOQ 20 pieces; lead time 30–35 days — contact the technical team for specifications
- —L32 is rated for implements up to 1,050 Nm at 540 rpm continuous demand
- —At 90 hp tractor output, L32 continuous torque provides a 25% safety margin over 840 Nm implement demand
- —For implements demanding more than 1,050 Nm, consider T8 (1,240 Nm) or T9 (1,560 Nm) in triangular tube
- —Individual units packed in cardboard with foam end protection and rust-inhibiting wrapping
- —Bulk orders: palletised in wooden crates with internal dunnage; 20 ft container capacity approximately 400 units
- —Incoterms: FOB Ningbo or Shanghai; CIF Santos available; DDP on request for large contracts
お客様の声
Eduardo S.
Rio Grande do Sul, Brazil — Square Baler Service Centre
★★★★★
- L32 is now our stock replacement shaft for all European-spec large round and square balers
- 35×94 mm cross kit cross-references correctly to the B07 spec in all European OEM parts books
- No adaptation required — lemon tube fits all the housings that refused T7N triangular tubes
Camila P.
Curitiba, Brazil — Forage Harvester Importer
★★★★★
- Specified L32 on a fleet of 12 pull-type harvesters — 800-hour service life confirmed in dense corn silage
- CE and ISO documentation complete on first shipment — customs clearance at Santos was straightforward
- Will move L32 to annual blanket order from next season
関連製品
配送および注文情報
最小注文数量
1個（在庫あり）
50個（カスタム）
リードタイム
7～10日（在庫あり）
25～30日（カスタム対応）
配送
海上LCL/FCLでブラジルへ
航空貨物輸送可能
取引条件
FOB 寧波 / 上海
CIFサントス利用可能
資格認定
CE認証取得済み
ISO 9001:2015
TS/16949
SGS検査LGPD準拠
OECDコード4シールド
